--- title: "Induction shows E2 and shuts off" description: "La Cornue induction shows E2 and shuts off: e2 is one of three codes La Cornue prints anywhere in its US documentation, and the manual's own explanation is…" url: "https://la-cornuemiami.support/symptoms/induction-shows-e2-and-shuts-off/" date_modified: "2026-09-03" Appliance type: "Cooktops and rangetops, Ranges" --- # La Cornue induction shows E2 and shuts off ### When does it happen? Three different answers, three different causes. During long cooking or on boost, with several zones running: that is heat building up in the electronics and the air path is the first suspect. Straight after a pan has boiled dry: the manual names that explicitly and the cooktop may simply need to cool. From cold, within minutes, every time: that is not a ventilation problem, it is the unit, and it needs measuring. Note which of the three yours is before you call — it is the most useful sentence in the conversation. ### What it usually means, by the kind of La Cornue appliance La Cornue sells one appliance in several forms, and the same behavior points at different things on each of them. A built-in side-by-side and an integrated column are not the same service situation, and a dual-fuel range and an induction range fail in different halves. - **All-induction Château** — The generator sits under the cooktop in a cabinet that also holds electric ovens. What is packed around it matters more here than anywhere. - **CornuFé 90 and 110 induction** — Factory-built installation with a defined air path. E2 here usually means the path has been closed off after the fact. - **Ceramic induction module in a gas Château** — Two zones and a smaller generator, but the same rule: it needs air it is not always given. ### Why the boring answer is usually the right one An induction generator is a power electronics assembly living in a kitchen cabinet under a hot cooktop, and everything about its reliability depends on air moving past it. What happens over the years is entirely ordinary: somebody fits a drawer unit, or stores pans and paper in the cavity, or a cabinet is closed in during a remodel, and the appliance quietly loses the air it was specified with. Nothing is broken. The cooktop overheats, protects itself, and prints E2 — which is exactly what it was designed to do. We look at that before we look at the board, because so does the manufacturer. ### What we will not do We will not clear the code, hand the range back and leave. E2 is a protection, and an appliance that trips it repeatedly is being cooked by its own environment; the board will eventually fail and the failure will not be covered by anything. So the report says what the air path actually is, what it should be, and — where the cabinet cannot be changed — what can be done instead. Where the installation is genuinely correct and the unit still trips, that is a problem, and we say so with the measurements behind it. Blocked or absent ventilation The maker's first suggestion. A drawer, a fitted cabinet or stored items closing off the air path under the hob. A pan boiled dry Named in the manual. The glass and everything under it get far hotter than cooking normally makes them. A cooling fan that has failed or clogged The electronics have active cooling and it can stop without any other symptom. A temperature sensor reading wrongly It reports heat that is not there and shuts a healthy generator down. A failing generator board Where the ventilation is right and it still cuts out from cold. Measured, then quoted with its lead time. Note when it cuts out Under load, after a boil-dry, or from cold. Three different problems. Look under the hob Whatever has been stored in that cabinet since the range was installed. This is genuinely often the answer. Listen for the fan A cooling fan you can no longer hear is a cooling fan to mention. Do not just reset and continue Repeated overheating is what kills the board this code is protecting. It cuts out under load What it usually means The maker's own first answer is ventilation, not electronics A pan boiled dry produces it too Resetting it and carrying on is how a generator board dies When does it happen? Three different answers, three different causes. During long cooking or on boost, with several zones running: that is heat building up in the electronics and the air path is the first suspect. Straight after a pan has boiled dry: the manual names that explicitly and the cooktop may simply need to cool. From cold, within minutes, every time: that is not a ventilation problem, it is the unit, and it needs measuring. Note which of the three yours is before you call — it is the most useful sentence in the conversation. What it usually means, by the kind of La Cornue appliance La Cornue sells one appliance in several forms, and the same behavior points at different things on each of them. A built-in side-by-side and an integrated column are not the same service situation, and a dual-fuel range and an induction range fail in different halves. All-induction Château — The generator sits under the cooktop in a cabinet that also holds electric ovens. What is packed around it matters more here than anywhere. CornuFé 90 and 110 induction — Factory-built installation with a defined air path. E2 here usually means the path has been closed off after the fact. Ceramic induction module in a gas Château — Two zones and a smaller generator, but the same rule: it needs air it is not always given. Why the boring answer is usually the right one An induction generator is a power electronics assembly living in a kitchen cabinet under a hot cooktop, and everything about its reliability depends on air moving past it. What happens over the years is entirely ordinary: somebody fits a drawer unit, or stores pans and paper in the cavity, or a cabinet is closed in during a remodel, and the appliance quietly loses the air it was specified with. Nothing is broken. The cooktop overheats, protects itself, and prints E2 — which is exactly what it was designed to do. We look at that before we look at the board, because so does the manufacturer. What we will not do We will not clear the code, hand the range back and leave. E2 is a protection, and an appliance that trips it repeatedly is being cooked by its own environment; the board will eventually fail and the failure will not be covered by anything. So the report says what the air path actually is, what it should be, and — where the cabinet cannot be changed — what can be done instead. Where the installation is genuinely correct and the unit still trips, that is a problem, and we say so with the measurements behind it. ### Can I keep using the cooktop if I avoid using all the zones at once? Managing around it works for a while and it is not a fix. Every trip means the electronics reached their protection limit, and semiconductors do not recover from repeated thermal stress — they just fail later, usually as an Er code and a board. If you need to keep cooking before the visit, use fewer zones, avoid boost, and let it cool properly between sessions. But get the air path looked at, because the cheap fix now is a considerably cheaper fix than the board later. ### Could the ovens underneath be causing it? On an all-induction Château they are worth considering, yes. When that cooktop is specified both ovens are electric, and everything is sharing one cabinet volume and one set of clearances. A long roast in the oven below while several induction zones run above is the worst case the assembly ever sees. That is not a problem, but it does mean the ventilation specification is not optional, and it explains why E2 shows up on holidays rather than on Tuesdays. --- **[Read full article: Induction shows E2 and shuts off](https://la-cornuemiami.support/symptoms/induction-shows-e2-and-shuts-off/)**